
Ceramic Sealing Gaskets
Product Description
Ceramic sealing gaskets are the thin ceramic sheets laid between two faces that must seal and must not conduct, and must not soften where rubber would degrade and where metal would short a live part to the body. They sit in joints on electrical equipment, chemical plant, pipework and machines, and they are usually the part that decides whether a joint holds: a gasket that is thicker along one edge loads the joint unevenly, and one that is thinner than the joint was cut for lets the two faces touch and the insulation is lost. Sheet is an awkward ceramic shape, because a thin body warps in the kiln and a warped gasket cannot seal.
A thin gasket is the part of a joint that nobody can adjust afterwards, so we grind both faces after firing instead of relying on the pressed thickness, and you get a sheet that is the same thickness across its whole area. Grinding both faces also takes off the fired skin, so the gasket does not stick to a hot flange when the joint is opened. Tell us the joint thickness and the bore layout, and we will produce gaskets to that take-up, in singles or as a set for the flange, so the joint goes together without a second gasket stacked behind the first.
Specifications

Application 1. Electrical equipment sealing joints. A joint between a live part and an enclosure has to seal and insulate at the same time. An alumina gasket does both, where a metal gasket would conduct and a rubber one would not survive the temperature.
Application 2. Chemical plant flange joints. Process chemistry attacks elastomer gaskets and swells them until the joint leaks. Alumina is inert to acid and alkali, so the seal does not change its thickness over the campaign.
Application 3. Hot pipe and machine sealing positions. A gasket between hot faces must not creep under clamping load. A ground ceramic sheet holds its thickness under the bolt load and does not relax at 1500°C.
Customization
Outside outline, bore diameter, bore positions, thickness and edge treatment are produced from drawing. Thickness is available from 0.5 mm to 20 mm, in 95% or 99% alumina, and both faces are ground. Buyers may specify the flatness band and the surface finish required by the joint, and gaskets can be supplied as singles or in sets for a flange. Drawings and samples are accepted, OEM and ODM are supported, and a sample takes about 15 days.
Packaging & Transportation
Gaskets are wrapped in bubble film, stacked flat in a rigid inner box so they cannot bend, and the box is filled to stop movement. Inner boxes go into export corrugated cartons; heavy or large-diameter sets are packed in fumigated wooden cases with the IPPC mark. Cartons carry fragile, this side up and keep dry marks, and a shipping mark with order number, carton number and destination. EXW and FOB Shanghai or Ningbo are available.
Specifications
|
Parameter |
Specification |
|
Material |
95% or 99% alumina ceramic |
|
Thickness Range |
0.5 mm to 20 mm |
|
Size Tolerance |
±0.1 mm or less |
|
Bulk Density |
3.6 g/cm³ or more |
|
Max Working Temperature |
1500°C |
|
Insulation Resistance |
Greater than 100 MΩ |

FAQ
Q1. Can you hold thickness on a thin gasket?
A. Yes. Both faces are ground after firing to the ordered thickness within ±0.1 mm, which is what a thin pressed sheet cannot guarantee across its area.
Q2. Which grade suits a chemical joint?
A. Both 95% and 99% alumina resist acid and alkali; the 99% grade is chosen where the joint also runs hot or where a tighter thickness tolerance is needed.
Q3. What is the minimum order?
A. Orders start at RMB 1,000 in value, which is enough for a trial set of one flange.
Hot Tags: ceramic sealing gaskets, China ceramic sealing gaskets manufacturers, factory, Abrasion Resistant Ceramic Tiles, Alumina Ceramic Pipe, Ceramic Guide Rail, Ceramic Idler Roller, Ceramic Nozzle Spray, Industrial Ceramics Products
You Might Also Like
Send Inquiry
