Ceramic Mounting Bases

Ceramic Mounting Bases

Ceramic mounting bases are the shaped insulating seats that hold a part in position inside an appliance, a heater, a lamp assembly or a piece of electronic equipment. The base locates the part at a fixed height, isolates it from the metal frame, and often provides the creepage path between two conductive parts that sit close together, so it belongs to the insulation system rather than to the brackets.
Send Inquiry

Product Description

 

Ceramic mounting bases are the shaped insulating seats that hold a part in position inside an appliance, a heater, a lamp assembly or a piece of electronic equipment. The base locates the part at a fixed height, isolates it from the metal frame, and often provides the creepage path between two conductive parts that sit close together, so it belongs to the insulation system rather than to the brackets. The shape is usually the design: a pocket for the part, a step that sets the height, ears for the screws and the ribs between them, all of which have to be on one datum or the part sits skewed. The seat face is the working feature, because a base that is not flat rocks what it carries.

 

These bases are usually made once and then needed for years, so we build the shape in one pressing tool rather than assembling it from plates: pocket, step, ears and ribs come off a single datum, and the seat is ground so the part sits flat without a shim. Send the component that sits on the base, or the outline drawing, and we will produce a sample for fit before the run. The tool stays with your part number, so the seat height you approved is the seat height you receive next time.

 

Specifications

01536fda-e9c1-45efd15273aa1c

Application 1. Heating appliance element seats. An element seat holds a hot conductor at a fixed height above the cavity floor. Alumina keeps that height at temperature and insulates the element from the body, so the appliance does not rely on an air gap alone.

Application 2. Lamp and indicator assemblies. A base locates the lamp holder and separates it from the metal housing. A flat, stable seat keeps the lamp at the designed position, and the ceramic body does not deform where the lamp heat reaches it.

Application 3. Electronic equipment mounts. A mount that carries a board or a sensor has to isolate it electrically and hold it level. A single pressed base keeps the mounting points coplanar, which avoids stressing the board when it is fixed.

Customization

 

Outline, seat height, pockets, steps, ribs, mounting ears and bore positions are produced from drawing in 95% or 99% alumina. Buyers may specify the seat flatness, the creepage distance between conductive parts, and the surface finish under the component. Drawings and samples are accepted, OEM and ODM are supported, and a custom sample takes about 15 days.

 

Packaging & Transportation

 

Bases are wrapped in bubble film with EPE over the seat face, then packed in an inner box sized to the outline so ears are not loaded. Inner boxes go into export corrugated cartons; heavy consignments are packed in fumigated wooden cases with the IPPC mark. Cartons carry fragile and this side up marks, and a shipping mark with order number, carton number and destination. EXW and FOB Shanghai or Ningbo are available.

 

Specifications

Parameter

Specification

Material

95% or 99% alumina ceramic

Max Working Temperature

1500°C

Insulation Resistance

Greater than 100 MΩ

Size Tolerance

±0.3 mm or less

Compressive Strength

2000 MPa or more

Bulk Density

3.6 g/cm³ or more

product-900-675

 

FAQ

 

Q1. Can a complex base be made as one piece?

A. Yes. Pockets, steps, ribs and ears are formed in one pressing tool, which keeps them on a single datum instead of stacking tolerances from separate parts.

Q2. How is the seat kept flat?

A. The seat face is ground after firing, so a component sits flat without a shim and the height repeats from order to order.

Q3. What is the minimum order?

A. Orders start at RMB 1,000 in value, sufficient for a trial base before a production run.

 

Hot Tags: ceramic mounting bases, China ceramic mounting bases manufacturers, factory, Alumina Ceramic Lining Tiles, Ceramic Base, Ceramic Guide Rail, Ceramic Nozzle Spray, Industrial Ceramic Balls, Sealed Ceramic Bearings

Send Inquiry

Send Inquiry