Ceramic Manicure Blades

Ceramic Manicure Blades

Ceramic manicure blades are the small cutting and buffing tips used on nail drills, callus tools and podicure instruments, where the tip has to cut cleanly, stay hygienic and not rust between uses. The edge is the product: an angle that is too blunt burns the nail instead of cutting it, an angle that is too sharp chips on first contact, and for a buffing tip the profile decides whether the surface is smoothed or scratched.
Send Inquiry

Product Description

 

Ceramic manicure blades are the small cutting and buffing tips used on nail drills, callus tools and podicure instruments, where the tip has to cut cleanly, stay hygienic and not rust between uses. The edge is the product: an angle that is too blunt burns the nail instead of cutting it, an angle that is too sharp chips on first contact, and for a buffing tip the profile decides whether the surface is smoothed or scratched. A tip also has to run true, because a bit that wobbles at speed vibrates in the hand and heats the nail. The body is alumina, which does not corrode, takes repeated disinfection and leaves no metal smear on the work.


These tips are consumed by the thousand by tool makers and distributors, so what you need is an edge that repeats rather than a single good sample. We grind the edge angle, the tip radius and the shank in one setup per tip, so the angle in your specification is the angle on every piece, and the run-out stays small enough that the tool does not vibrate. Send the angle and the profile you sell, or a tip you want matched, and we will produce a sample batch for your trial before the production order.

 

Specifications

01536fda-e9c1-45efd15273aa1c

Application 1. Nail drill bits and burrs. A bit runs at speed against a nail, so any run-out or dull edge shows as vibration and heat. A ground alumina tip holds its angle and its concentricity, so the cut stays clean through the life of the bit.

Application 2. Callus and podicure tools. These tools contact skin as well as nail, and they are disinfected between clients. Alumina does not corrode under repeated disinfection and its edge does not turn over, so the tool keeps its cut.

Application 3. Buffing and finishing tips. A finishing tip decides whether a surface is smoothed or scratched, and that is set by the edge profile. A held profile reproduces the same finish from tip to tip.

Customization

 

Edge angle, tip radius, tip profile, shank diameter, overall length and shank end are produced from drawing in 99% alumina. Buyers may specify the edge angle for a cutting or a buffing function, the radius at the tip, and the shank form that fits their handpiece. Drawings and samples are accepted, OEM and ODM are supported, and a custom sample takes about 15 days.

 

Packaging & Transportation

 

Tips are wrapped in bubble film and packed in a small rigid inner box, or in a tip holder where one is specified, so the edge cannot be touched. Inner boxes go into export corrugated cartons. Small high-value sets may travel in fumigated wooden cases with the IPPC mark. Cartons carry fragile and this side up marks, and a shipping mark with order number, carton number and destination. EXW and FOB Shanghai or Ningbo are available.

 

Specifications

Parameter

Specification

Material

99% alumina ceramic

Hardness

HRA90 or more

Bending Strength

300 MPa or more

Max Working Temperature

1500°C

Size Tolerance

±0.05 mm or less

Edge Angle

Customizable

product-900-675

 

FAQ

 

Q1. Can the edge angle be made to our specification?

A. Yes. The edge angle is ground to the angle in your instructions and finished per tip, so every piece in the batch cuts at the same angle.

Q2. Will the tips stand up to repeated disinfection?

A. The body is alumina, which does not corrode or take up water, so repeated disinfection does not dull the edge or change the tip outline.

Q3. What is the minimum order?

A. Orders start at RMB 1,000 in value, which covers a trial batch before a production order.

 

Hot Tags: ceramic manicure blades, China ceramic manicure blades manufacturers, factory, Alumina Ceramic Ring, Alumina Ceramic Rod, Ceramic Industrial Blades, Industrial Ceramic Balls, Industrial Ceramics Products, Sealed Ceramic Bearings

Send Inquiry

Send Inquiry