
Abrasion Resistant Valve Liners
Product Description
Abrasion resistant valve liners are the ceramic sleeves and seat pieces fitted inside slurry valves, discharge valves and ash handling valves, where the medium is a mixture of liquid and hard particles that destroys a metal trim in weeks. The liner is a replaceable wear part with a defined bore, and that bore is what keeps the valve's flow characteristic: once the liner has worn oversize the valve no longer controls the flow it was sized for, it simply passes more. Liners are produced to the valve body drawing so the outside seats in the body and the bore stays where the trim was designed, and the material also resists acid and alkali so one liner covers an abrasive slurry that is chemically active as well.
A valve liner is replaced on a schedule, so the part you fit has to go into the body as supplied and wear like the one it replaces. We produce the liner to the valve body drawing with the outside configuration and the bore held together, check the bore on the finished piece, and keep the tooling for your part number, so a liner ordered a year later seats without the valve being re-machined. Tell us the medium, or send a worn liner, and we will agree the grade and the bore so the valve keeps the characteristic your process was set around.
Specifications

Application 1. Slurry and tailings valves. A slurry valve trim wears where the particles turn at the seat. An alumina liner takes that wear and holds its bore, so the valve keeps its flow characteristic instead of passing more and more as the trim opens up.
Application 2. Ash handling and discharge valves. Ash is abrasive and often hot, and a metal trim deforms as well as wears. Alumina holds its shape at 1500°C, so the seat geometry stays and the valve still closes.
Application 3. Chemical slurry service. Where the slurry is also acid or alkaline, a metal liner corrodes as it wears. Alumina resists both, so the replacement interval is set by wear rather than by corrosion.
Customization
Body fit configuration, liner bore, wall thickness, seat angle and end faces are produced from the valve body drawing, in 95% or 99% alumina. Buyers may specify the bore that sets the flow characteristic, the grade for a chemically active medium, and whether the liner is supplied as a single piece or as a set with the seat. Drawings and samples are accepted, OEM and ODM are supported, and a custom sample takes about 15 days.
Packaging & Transportation
Body fit configuration, liner bore, wall thickness, seat angle and end faces are produced from the valve body drawing, in 95% or 99% alumina. Buyers may specify the bore that sets the flow characteristic, the grade for a chemically active medium, and whether the liner is supplied as a single piece or as a set with the seat. Drawings and samples are accepted, OEM and ODM are supported, and a custom sample takes about 15 days.
Specifications
|
Parameter |
Specification |
|
Material |
95% or 99% alumina ceramic |
|
Hardness |
HRA90 or more |
|
Bulk Density |
3.6 g/cm³ or more |
|
Compressive Strength |
2000 MPa or more |
|
Max Working Temperature |
1500°C |
|
Size Tolerance |
±0.5 mm or less |

FAQ
Q1. Will the liner fit the valve body without re-machining?
A. Yes. The liner is produced to the body drawing and the tooling is retained, so a replacement seats in the body as supplied.
Q2. Which grade should be used for a chemical slurry?
A. 95% covers a straightforward abrasive slurry; the 99% grade is used where the medium is also acid or alkaline and the liner has to resist both.
Q3. What is the minimum order?
A. Orders start at RMB 1,000 in value, which covers a trial liner for one valve.
Hot Tags: abrasion resistant valve liners, China abrasion resistant valve liners manufacturers, factory, advanced ceramics, Alumina Ceramic Products, Ceramic Valve Liner, Chemically Bonded Ceramics, Specialty Ceramics
You Might Also Like
Send Inquiry
