Semiconductor Grade Alumina Ceramics

Semiconductor Grade Alumina Ceramics

Semiconductor grade alumina ceramics are the parts that sit close to the wafer or inside the process chamber, where the material has to be clean, stable and electrically insulating rather than merely strong. They are used as wafer handling parts, chamber internals, insulating plates, nozzles and locating bodies in equipment where a particle or an ion released from the part becomes a defect on the product.
Send Inquiry

Product Description

 

Semiconductor grade alumina ceramics are the parts that sit close to the wafer or inside the process chamber, where the material has to be clean, stable and electrically insulating rather than merely strong. They are used as wafer handling parts, chamber internals, insulating plates, nozzles and locating bodies in equipment where a particle or an ion released from the part becomes a defect on the product. What makes the part suitable is not one figure but the combination: a dense body with closed porosity, a surface that can be cleaned without breaking down, and a shape that holds its dimensions through thermal cycling so the wafer sees the same gap on the first run and the hundredth.


In wafer handling, one contaminated part can cost a batch, so the part has to arrive clean and stay clean. We press and fire the body in house, finish the surfaces that face the wafer as a separate operation to remove the fired skin, and clean and wrap each part before it leaves, so you are not the one who has to recover the surface. For a new chamber design, we produce a prototype and measure it against your drawing first, which lets you qualify the part before committing to a tool and a production batch.

 

Applications

01536fda-e9c1-45efd15273aa1c

Application 1. Wafer handling components. A handling part touches the wafer directly, so any particle on its surface becomes a defect. A dense, closed alumina body with a finished surface reduces the chance that the part itself is the particle source.

Application 2. Insulating sections in vacuum chambers. Inside a chamber the insulator must hold voltage without outgassing. High-purity alumina has very little volatile content, so it does not disturb the vacuum or deposit on the wafer.

Application 3. Plasma-facing supports and fixtures. Plasma erodes metals and attacks polymers, but a dense alumina surface resists it. The part keeps its shape and its insulation, so the process stays stable over a longer campaign.

Customization

 

Parts are produced from drawing in a purity grade selected for the process: outline, bores, pockets and wall thickness are all machined to the chamber interface, and the surface finish is set to the particle and sealing requirement. Physical samples are also accepted as the production basis. OEM and ODM are supported, and a custom sample runs about 15 days. Where a part must fit an existing chamber, a prototype is checked before tooling.

 

Packaging & Transportation

 

Each part is wrapped in bubble film or EPE and separated in a foam-lined inner box, since a chipped edge is a scrap part in this application. Inner boxes go into export corrugated cartons; heavy or large pieces are packed in fumigated wooden cases with the IPPC mark. Cartons carry fragile, this side up and keep dry marks, and a shipping mark with order number, carton number and destination. EXW and FOB Shanghai or Ningbo are supported.

 

Specifications

Parameter

Specification

Material

99% or more alumina ceramic

Bulk Density

3.6 g/cm³ or more

Bending Strength

300 MPa or more

Dielectric Strength

15 kV/mm or more

Max Working Temperature

1600°C

Size Tolerance

±0.5 mm or less

product-900-675

 

FAQ

 

Q1. Are these parts certified for semiconductor use?

A. No third-party certification is held yet. The ISO 9001 quality system has passed internal audit and the certification application is being prepared, so qualification testing is normally done by the buyer on samples.

Q2. Can you supply a sample before a chamber is committed?

A. Yes. A prototype is produced from your drawing or sample in about 15 days, so the fit and the surface condition can be checked on the tool before a production order is placed.

Q3. What is the minimum order value?

A. Orders start at RMB 1,000 in value, which allows a trial quantity of one part number before a full production run.

 

Hot Tags: semiconductor grade alumina ceramics, China semiconductor grade alumina ceramics manufacturers, factory, Ceramic Point Needle, Ceramic Wire Guide Plate, electrical ceramics, Electrical Electronic Ceramic, Pottery Light Fixtures, Temperature Control Ceramic

Send Inquiry

Send Inquiry